Available Equipment

Air Compressors:

Description: Curtis Air Compressor; size 15HP; capacity 120 gallon tank.
Ref.#: 50220
 

Boring Machines:

Description: Double end trim bore, model MVB, 84" width capacity, (10) 1-1/2 HP, 1800 RPM spindle motors, each spindel can be turned on and off with a single switch, spindle stoke 4", boring area 20" x 61", 2HP hydraulic feed pump, no template frame or templates, connected 440V.
Ref. #: 50067
 
 
Description: 212, Horizontal, (6) heads - 2 HP each, feed motor 5 HP, individual air holddowns for each spindle and a self centering device to divide the length between leaf and the table.
Ref. #A-637
 
Description: Drill Press, model 1200, 2HP, 10" capacity, 20" x 22" table, 220/440V, 3Ph, 60Cy, connected 220.
Ref. #50219
 
Description: Model CH, 7.5 HP, 4-spindle, 1.5 HP pump.
Ref.#: 50139
 
Description: Model CHX, 10 HP, 10 spindle double shaft, 1.5 HP pump.
Ref.#: 50138
 
Description: (5) 1 hp direct drive motors; tablesize of 14" x 96"; set up for independent spindle arm operation; no template rack.
Ref.#: 50300
 
Description: Equipped with (4) 1hp, direct drive spindles; table size of 54" x 16"; 2 hold-downs; spring action; includes (3) drill heads; (1) 2-spindle; (2) 3 spindle.
Ref.#: 50307
 
Description: Model B 100; connected 220 V; 3/4 HP; 15/32 - 7.24 center.
Ref.#: D-8712
 

Carving Equipment

 
Description: Model 25; 3hp; flat belt drive motor; spindle length of 10" extended; cast iron spindle frame; fabricated steel base.
Ref. #: 50303
 

Door Equipment

 
Description: Model 250MC Raised Panel Door Machine - 50" cut length, 3PH 220V, 20A & 7-1/2 HP motor, 1-1/4" spindle, (1) 998 1-1/8" rise standard template consists of 4 panel and 4 matching rail templates, (1) set insert tooling, (3) carbide cutters with inserts for cope, rail and panel.
Ref. #: 55116
Description: Model P1318; voltage: 220/440/120; 1 - 2 phase; 60 cycle; 3 only black & decker router units 120/60/1 V; 8 AMP; 25,000 RPM; drive motor 1/3 HP ratio 11 - 1; 2 only hole boring unit; sold as a set with #50252 for $7,500.00.
Ref. #: 50251
Description: Model E-1302; Sold as a set with #50251 for $7,500.00; connected 220 V; 1 only sanding unit with 3" x 8" belt; 1 only 4" x 6" straight knife cutter head; 1/3 HP drive 1725 RPM.
Ref. #: 50252
 
Description: Clary 435 Doorcraft III. An economical machine that sizes, bevels, machines and mortises both interior and exterior doors. Sizer and convenient power control panel handles door width from 1'0" to 3'0" at 2" increments. Centering and clamping device insures lock position always in the center door. Indexing mechanism handles doors from 1'0" to 3'0" at 2" increments. Boring and routing devices; tension roller to stabilize the door; pedal for raising door into position for boring and routing; foot pedal for boring bolt hole.
Ref. #: C-1186
 

Dust Collector/Air M-UP

 
Description: Model C730-3 Dust Collector- New in showroom; 3PH 220/440V 60 Cy,
7 1/2hp with 3 collector/filter unit, includes silencer and starter.
Ref. #: 55132

 

Description: Dust Collector-Pipe and Fitting for Dust Collector (55132), quick-fit.
Ref. #: 55133
 
Description: Model 1000; 10 HP; 4000 CFM; connected 440 V; 3 bags.
Ref. #: 50230
 
Description: Model 500; 5 HP; 2 bag; connected 220 V.
Ref. #: 50243
 
Description: Model 19T5, Dust Collector, capacity 2000 CFM, one bag drum, connected 440.
Ref.#: 50232

 

Edgebanders:

Description: Model 1408 Edgebander, capacity 0.4-20MM, end trim-0.55 KW, top & bottom trim belt 10 KW, top & bottom buff-0.25 KW, pellet type glue system, connected 220
Ref. #: 50194

 

Grinders:

Description: Model 152A, 3/4 HP motor, 2850/3450 RPM, 3 stop pulley, 11/16" diameter shaft, table travel 18"
Ref. #: A-357
 
Description: Model 411N, 2 HP motor, 2'8" x 1-13/16" arbor.
Ref. #: 50012
 
Description: Model 231, 28" table travel, 1-1/2 HP. The table is manually operated. The unit has stands for supporting.
Ref. #: A-358
 
Description: Model 152A; 3/4 HP; 16" capacity; connected 220V
Ref. #: 50180
 
Description: Model K, 1.5 HP motor, table travel 19" right to left, 6" in and out, 12" up and down, used 6" wheels.
Ref. #: A-360
 

Jointers:

Description: Model 660, (2) 5 HP direct drive cutterheads, 4-1/2" max. thickness, chain feed each side with automatic oiler, staggertooth carbide heads, 5 HP, 4 speed motor.
Ref. #: D-8863-C
 
Description: Model 199; capacity 16"; infeed table 48.5"; outfeed table 36"; cutterhead 3 knife; backfence tilting 49.25"; horsepower 5; voltage 220/440.
Ref. #: D-8536
 

Lathes:

Description: Model T5, lathe has V-belt drive, 5 belts to main arbor. Air operated automatic feed, custom installed. Work turned by 1-1/2 HP, 4 speed motor through gear reducer. Feed motor straight 440 V. This lathe would have to be rewound to be operated on 220 V. at an extra cost.
Ref. #: D-8129
 
Description: Lathe Set Up Stand, Standard 2-5/8", 43" capacity.
Ref. #: 50081
 
Description: Lathe Set Up Stand, Standard 2-5/8", 36" capacity.
Ref. #: 50080
 
Description: Grinder has a 30"x 60" table, wire brush and 1/2" grinding rock.
Ref. #: 50082
 
Description: Grinder has stand with lighted eye shield and manual controls.
Ref. #: 50083
 

Mortisers:

Description: Model 212, (6) 2 HP spindles - 3500 RPM, 5 HP feed - 1160 RPM, 6 heads. Feed speed variable, table size 13" x 160". Connected 440 V.
Ref. #: A-638
 

Moulders:

Description: Feed Through, 10 HP - 1800 RPM, 2" x 6" capacity, belted moulder, all heads pulled by 10 HP motor. Motor has two (2) magnetic starters and one one (1) set of square heads on machine. Connected 220.
Ref. #: D-8274
 
Description: Model 464, 4 head, 4" x 6" capacity, 7.5 HP top and bottom heads, 5 HP side heads, 5 HP Reenes drive feed, 1-13/16" diameter side spindles, 2-1/8" diameter horizontal spindles, connected 220 V.
Ref. #: D-8510-C
 
Description: Model 272, 4' x 2' capacity. This unit has 5 HP top and botton heads with 4 HP side heads, 2-1/8" diameter horizontal and 1-3/16" diameter vertical spindles, 8-speed, 3 HP feed.
Ref. #: D-8363
 
Description: Model 276, 4 head, 4" x 6" capacity. Head sequence: top and bottom - 10 HP, left and right - 7.5 HP, feed speed 7.5 HP, includes hopper, connected 220 V.
Ref. #: D-8846
 
Description: Model 274; 4 x 4 capacity; connected 220 V; top 5 HP; left 4 HP; right 4 HP; bottom 5 HP; 4 step pulley feed.
Ref. #: D-8855
 

Planers:

Description: Model 177, 30" X 14" capacity, 4-knife - 3,600 RPM top and bottom cutterheads, 40 HP top head, 25 HP bottom head, 5 HP feed. Sectional infeed rolls and chip breakers. Power raise and lower of bed. No grinding equipment. Grinding equipment can be furnished at an additionl charge of $4,500.00. Connected 440 V.
Ref. #: D-8046
 
Description: Model 66, 40" x 8" wide opening on bed, 30 HP direct drive on cutterhead (40" quiet-cut head), 3/4" HP table raise and lower motor, 5 HP feed system (fixed), sectional infeed rollers with 2" wide spring loaded sections, sectional chipbreakers, adjustable pressure bar, bed rollers - all adjustable from the front of planer, connected 440 V.
Ref. #: D-8862-C
 
Description: Model 225; 15 HP; 24" capacity; connected 440 V; 4 knive high speed steel; 4" feed rolls; variable speed feed (20 - 100 FPM); maximum depth of cut is 1/2"; stock thickness 1/8" - 8"; comes with grinder; weight = 3342 lbs.
Ref. #: 50233
 
Description: Model 55; 40 HP top; 30 HP bottom; 30" x 14" capacity; connected 220 V; thickness 1/4" x 14"; shortest 28"; butted 12"; 7.5 HP feed; power raise and lowering 1/2 HP; with grinder and jointing attachment; 10,000 lbs.
Ref. #: 50250
 
Description: Model 110; 36" x 8" capacity; 20HP cutterhead motor; 6-knife cutterhead; powered raise and lowering bed; 4 speed feed motor feed rates are standard at 25, 40, 50 and 80 FPM, grinding equipment. Approximate weight 8,300 lbs.
Ref. #: D-8452
 

Routers:

Description: Model 434, 5 HP, 28" throat. This router has a table size of 24" x 36" and a table height adjustment of 10". The table does not tilt. This router runs at two (2) speeds, 10,000 RPM and 20,000 RPM. The collet size is 3/4". The spindle movement is 4" up and down with 3 positions.
Ref. #: D-8466
 
Description: Model A-1, 5 HP, 14,100 RPM, 72" reach. Unit does not have table. Equipped with 5 KW frequency changer.
Ref. #: A-605
 
Description: Model A-1, 5 HP, 14,100 RPM, 72" reach. Unit does not have table. Equipped with 5 KW frequency changer.
Ref. #: A-607
 
Description: Model 910, 5 HP, 30" Capacity, 220/440 Volts, 3 Phase, 60 Cycle, Connected 220V.
Ref. #: D-8631
 
Description: Model 920FH, 7.5 HP, 1/2" capacity, 220/440 Volts, 3 Phase, 60 Cycle, Connected 440V.
Ref. #: 50122
 
Description: Model UXB Wadkin Router; 36" capacity; 5.5 HP; 4 speed; motor speed 3420/1700; connected 440.
Ref. #: D-8877
 

Wide Belt Sanders:

Description: Model 401-37 Wide Belt Sander series 400, heavy duty frame, 20 HP, 36" capacity, belt length 60", belt widths 37", 44", 17" infeed conveyor bed extension, 5 1/2" rubber contact drum head for heavy sanding, belts can be changed in minutes.
Ref. #: 55059
 
Description: Model A3760 Wide Belt Sander, 20HP, capacity 36" x 5", 1 HP feed, power raise & lower, variable speed 15-20 fpm, 15" of front loading area, amp load meter, electric eye tracking, combination contact roll platen head, 37" x 60" abrasive belt.
Ref. #: 55105
 
Description: Model RB-37, (1) Head, 36" width capacity, combination sanding head with 4" diameter contact roll & 2" diameter wide polishing platen, 15 HP motor, 1 HP feed motor, abrasive belt size 37" x 60", air tensioning, electronic abrasive belt tracking, 1 HP single speed conveyor feed, 0" to 8" opening with (4) screw jacks, double infeed and outfeed rubber covered hold down rolls. Connected 220V.
Ref. #: 50034
 
Description: Model 24, 50 HP with stearns brake, 24" wide x 4" thick, unit has air tracking, belt feed with 1 HP motor through dodge speed reducer with a ratio of 24.89/1. This machine is capable of light abrasive sanding. Connected 440V.
Ref. #: D-8159
 
Description: Model 24, 50 HP with stearns brake, 24" wide x 4" thick, unit has air tracking, belt feed with 1 HP motor through dodge speed reducer with a ratio of 24.89/1. This machine is capable of light abrasive sanding. Connected 440V.
Ref. #: D-8158
 
Description: Model 36, (1) head, 37"capacity, platen head for finish sanding, 30 HP main motor with 1/3 HP feed motor. Connected 220V.
Ref. #: 50035
 
Description: Model LES4-1300, Wide Belt Sander, 1st, 2nd, 3rd, and 4th head, 30 HP, 7.5HP on feed, 7.5HP on blower with 8" opening, connected 440.
Ref. #: 50090
 
Description: Model UV-4521, 30 HP on head, 50" single head polishing shoe, power raising and lowering of bed, air tracking, motor V-belted to head, 7-1/2 HP. Variable speed feed, speed reducer with a ratio of 27 to 1. Connected 440V.
Ref. #: D-8247
 
Description: Model #3371HDUV; 25 HP; 5" x 36" capacity; connected 440 V; explosion proof electric boxes.
Ref. #: 50288
 

Sander-Misc.:

Description: Model 70, 30 HP, 100" double belt, power raise and lower, 1 HP feed.
Ref. #: D-8852
 
Description: Model 205 Edge/Slack Belt Sander, 3 HP, 5" capacity, platen length 50", belt speed 3100fpm, idle pulley dia. 3", floor space 24" x 74".
Ref. #: 55022
 
Description: Model 50, 5 HP, 220/440 electrical volts, 3 phase, 60 cycle, 30" capacity, has been changed on drive, to gear box, 10 spindle, 220 Connected.
Ref. #: 50159
Description: 5 HP, 6" belt, 36" x 96" capacity, pulleys are rubber covered and are 16" in diameter.
Ref. #: A-852
 
Description: 5 HP, 1750 RPM, 8" belt, table 36" x 96" capacity, (2) 16" x 6-1/2" pulleys. Connected 440V.
Ref. #: A-853
 
 
 

Saws-Band:

Description: Band Saw, 5 HP, direct drive motor, 36" capacity, 20" under guide, 45 degree tilt 36" x 37" tables, 19' 4" blade, size 5HP, 220/440V,3PH,60CY. Connected 440V.
Ref.#: 50169
 
Description: Band saw; length of saw blade 18'3" with carter guides; spoke wheel on top; 5 HP; capacity 36"; connected 220
Ref.#: 50168
 
Description: 2 HP; 16" capacity; connected 220V; no fence.
Ref.#: 50221
 
Description: Model DB-80; 5 HP; 32" capacity; includes standard accessories & dust hood 4" o.d.; 18.5" cutting height; 218.5" min. blade length; 227" max. blade length.
Ref.#: 50244
 
Description: Model GHE; 5 HP; 9" under guide; connected 440 V; 35" throat with hydraulic brake & work light; 36" x 37" table.
Ref.#: 50276
 
Description: Model 273-D; 2 HP; 36" throat; connected 440 V; 3" thickness under guide; 34" x 34" table size.
Ref.#: 50277
 
Description: 5hp; direct drive motor; tilting table size 32"l x 28"w; throat clearance height of 13"; table height of 40" from floor.
Ref.#: 50305
 
Description: Model B-5889; direct drive; 5hp motor; tilting table; table size of 36" x 36"; table height of 42" from floor; throat clearance height of 16".
Ref.#: 50306

 

Saws-Cut-off & Mitre:

 
 
Description: Model 43-20 J, left hand hydraulically operated cut-off saw with 20" stroke, 7.5 HP - 3450 RPM arbor motor, 3/4 HP hydraulic pump motor, 1-1/8" arbor saw, 16" infeed roller table, 8" outfeed table with 10 stops.
Ref.#: D-8858-C
 
 
Description: Model 43-20 S; 5 HP; 16" blade; connected 220V; no guard
Ref.#: 50181
 
Description: Model PS-50, 7.5 HP, 20" blade capacity, 24" stroke, depth of cut - 6", connected 220V.
Ref.#: 50064-C
 
Description: Model PS-50, 7.5 HP, 20" blade capacity, 24" stroke, depth of cut - 6", connected 220V.
Ref.#: 50063-C
 
Description: Model 212L, Cut-Off-Saw, 10 HP, 18" blade capacity, blade speed: 3,165 RPM, cycle speed: Up to 60 per minute. Air cylinder: 2" x 10", CFM 14.04 SCFM/2.18 CFM, Table height: 36" floor space: 25"x 28-1/2", electrical 220/440, 3PH, 60CY, connected 220.
Ref.#: 55092
 
Description: Model 212L, Cut-Off-Saw, 10 HP, 18" blade capacity, blade speed: 3,165 RPM, cycle speed: Up to 60 per minute. Air cylinder: 2" x 10", CFM 14.04 SCFM/2.18 CFM, Table height: 36" floor space: 25"x 28-1/2", electrical 220/440, 3PH, 60CY, connected 220.
Ref.#: 55070
 
Description: Model K18-20, 7-1/2 HP motor, 16" blade, 2 HP hydraulic feed, depth of cut - 4", 19" stroke on saw head. Connected 440V.
Ref.#: 50013
 
Description: 5 HP, 16" capacity.
Ref.#: 50119
 
Description: 5 HP, 16" capacity.
Ref.#: 50121-C
 
Description: Model DM-400; 7.5 HP; 16" - 20" blades; connected 220 V; magnetic starters; no hold down; air with seal check; hand control.
Ref.#: 50271
 
 
Description: Model 212 R; 10hp belt drive saw motor; 18" blade with capacity of 4" x 10"; 2" x 12"; 1" x 13"; 45 cycles per minute.
Ref.#: 50301
 
Description: Model C 500 R; 5 HP; 14" blade; right hand; 2" x 8" cutting capacity.
Ref.#: D-8561
 
Description: Model C 500 R; 5 HP; 14" blade; connected 440 V; 2" x 8" cut; up to 90 SPM.
Ref.#: D-8745
 

Saws-Gang Rip:

Description: Model SM/120, 60 HP, 220/440 volt main motor 2HP, 220/400 volt feed motor, magnetic starter with overload protection, automatic chain lubrication, ammeter, saw cartridge with spacers, four rows of anti-kick-back fingers, electric movement (up & down) of presser rollers, automatic shut down on main power when motor is highly stressed, gear drive system, feed track speed inverter controlled, variable speed on track speed, electrical components meet CSA standards, emergency stop, tool kit.
Specifications: Max. depth of cut 4 3/4", max. working width 11 7/8", feed track width 12 1/2", feed speed variable 0-130 FPM, throat depth 11 7/8", min. board length 23", saw blade dia. 250-350mm, arbor size 45mm, saw cartridge dia. 70mm, upper dust outlet dia. 9 3/4", lower dust oulet dia. 6", net weight 4620 lbs. Warranty 2- years electrical, 2 years mechanical.
Ref.#: 55062

 

Description: 50 HP, 4" thick, 13" arbor with 70mm O.P. largest diameter saw blade - 13 3/4", smallest diameter saw blade - 8 1/2", feed speed 0-118 feet per minute, feed motor - 2 HP, distance between first and last blade - 12 1/2", minimum length of workpiece with device - 19 5/8".
Ref.#: 50124
 
 

Saws-Gang & Slat Bed:

Description: Model PO-280; 50 HP; 12" blade capacity; connected 440V; 12" dip chain; 1 set spacers; 2 speed feed 5-20 / 10/40 meter; 1st speed - 16 ft/66 ft per min.; 2nd speed - 33ft/131 ft. per min; variable speed.
Ref.#: 50239
 
 

Saws-Radial Arm:

Description: 20" Blade Capacity, 7.5 HP, 1 HP hydraulic
feed, 220/440 Volts, 3 Phase, 60 Cycle, connected 220V.
Ref.#: 50145-C
 
Description: Model X-36AF, Size 5 HP, capacity 18", electrical 220/440 Volts, 3 Phase, 60 Cycle, connected 220V.
Ref.#: 50177
 
 
Description: 10" capacity, 2 HP, 18" cut, 220/440 Volts,
3 Phase, 60 Cycle, connected 220V.
Ref.#: 50144
 
Description: Model T-1853, 18" blade capacity, 1" arbor, upper and lower safety guards, safety spring return device, 5 HP, maximum depth of cut - 4-3/8", maximum cross cut - 24", connceted 220V.
Ref.#: 50029
 
Description: Radial Arm Saw, model GE, 16" capacity, 20" cut, 220/440V, 3Ph, 60Cy, connceted 220V.
Ref.#: 50223
 
Description: Radial Arm Saw, 5HP, model GE, 16" capacity, 20" cut, 220/440V, 3Ph, 60Cy, connceted 220V.
Ref.#: 50222
 
Description: Model 6, 5HP, 16" capacity, with 18" cross cut 220 connected.
Ref.#: 50149
 
Description: Model 450, 5HP, 14" blade, 16" cut, 220/440V, 3Ph,60Cy, connected 220.
Ref.#: 50109-C
 
Description: Model 3521; 5 HP; 14" capacity; connected 220 V; 16" cross cut; 26" x 48".
Ref.#: 50282
 
Description: Model T-1854; 5 HP; 16" blade; connected 220 V; type AA; 30" x 50"; spring return.
Ref.#: 50283
 

Saws-Panel:

Description: Model 54HS, 5 HP motor, 16" saw blade, depth of cut - 6", cutting length - 4' on two rails, complete with table system, 11" vertical machine height adjustment by hand wheel, variable speed automatic saw travel with adjustable length of cut, pneumatic hold down bar, connected 440 V.
Ref.#: 50001
 
Description: 10' cut, 7-1/2 HP, 12" blade. Unit has 1/2 HP scoring saw. Non-tilting arbor. Main saw arbor diameter 30mm, scoring arbor diameter 22mm. Unit is in good condition as it came from service.
Ref.#: A-812
 
Description: Model Z-45; 12 HP; connected 440 V; 177" cutting length; 153.5" cutting depth; 3.5" cutting height; 44.3/88.6 feed speed; 1.5 HP scoring; 9.84 FPM pusher; 1500 x 500 mm fixed front.
Ref.#:50273
 
Description: Model SI-320; 9 HP; 12" blade with 100MM scoring; Connected 230V; 59" rip capacity; 126" Crosscut length; 1" Main blade arbor; .75" Scoring arbor bore; Magnetic starter with overload protection; Overarm guard; Anodized aluminum table; Rear fixed table extension; Articulating support arm; Eccentric clamp; Weight 1575 lbs.
Ref.#:50240

Saws-Rip:

 
Description: MasterRip is an over cutting straight-line ripsaw with years of proven reliability in the woodworking industry. The 20 HP main motor directly drives a 1-1/2" saw mount arbor for a 4" capacity thickness cut. A 2 HP feed motor provides variable speeds from 60 to 180 ft. per minute. Two rows of anti-kickback fingers are mounted above and one set of anti-kickbacks are mounted in the table. A one piece chain minimizes maintenance and assures glue line accuracy. Ruggedly constructed form one piece cast iron and will provide years of top performance.
Ref.#: 55091
 
Description: Roll Feed Panel Rip Saw, model 191RF, 72" effective rools and holddown width, 30HP, 3600 RPM with 4 Uni-Hubs driven by splined shaft adjustable from L.H. side, 3HP with magnetic brake, torque limiter and reducer, feed speed 30-150 fpm, 72" x 71" drive rollers. Fixed vertical roller fence on RH side, connected 440.
Ref.#: 50165
 
Description: Model 15 Straight Line Rip Saw, size 15 HP, 12" capacity blade, 3 HP feed, 28" throzt, connected 220.
Ref.#: 50201
 
Description: Model #C12RS; Connected 220V; 15 HP motor; upper holdown rolls: 6; saw blade diameter: 8-12"; saw arbor diameter:1"; saw arbor speed: 4500rpm; saw arbor motor:15 HP, 230/460V/3 ph; feed motor: 2 HP; speed range (variable): 45-120 fpm; min. workpiece length: 8"; max. cutting thickness: 3 3/8"; distance from column to center of chain: 18"; table height: 31 1/2"; table dimensions: 39"W x 57"L; floor space: 47" x 63"; weight: 2090lbs
Ref.#: 55134
 
Description: Model #SL 52; 20 HP; 14" blade; connected 440 V; feed motor - 3 HP variable speed; feed speed - 65-190 FPM; width of table to the right of the saw is 25"; width of table to the left of the saw is 36"; length of table is 80"; weight - 4500 lbs.
Ref.#: 50265
 
Description: Model #SL 52; 20 HP; 16" capacity; connected 440 V; glue joint capacity; 28 AMP load; 79" x 64" table size; 3 HP; variable speed motor; 60/190 FPM.
Ref.#: 50286
 
Description: Model #75; 10hp direct drive saw motor; 4-speed feed chain; table size of 71"l x 64" w; 36"to left of blade; locking fence with ruled bar; drip oiling system for feed chain; 5" under hold-down rollers.
Ref.#: 50297
 
Description: Model #75; 20hp direct drive saw motor; 4-speed feed chain; table size of 71"l x 64" w; 36"to left of blade; locking fence with ruled bar; drip oiling system for feed chain; 5" thickness capacity.
Ref.#: 50298
 

Saws-Table:

Description: Model 34-444, contractor's saw with jet lock fence, 40" by 27" table, 1.5 HP, 10" capacity.
Ref.#: 50131
 
Description: Table saw, model 66, 5HP, 10" capacity, 28" x 38" table, 220/5440V,3Ph, 60Cy.
Ref.#: 50225

 

Description: 5 HP, 12" - 14" blade, 1" arbor, 48" x 3' table, tilting arbor.
Ref.#: 50017-C
 
Description: Model No. 4; 7.5 HP; 16" - 18" blade; connected 440 V; 1 mitre gauge; no guard.
Ref.#: 50269
 
Description: Model 511; 5hp; direct drive motor; 3480 rpm; tilting arbor; 0 degrees to 45 degrees; mechanical arbor brake; table size of 44" x 44"; 25" to right of blade; mitre bar in dovetail slot; no rip fence.
Ref.#: 50304
 

Saws-Trim & Bore:

Description: Model 24; trim motors; 2hp; 7430 rpm; direct drive drill motors; 2sp; 6840 rpm; direct drive coupling. Drill heads: 8 spindle w/various centers. Saw blades are 16" diameter, 7' opening maximum, 13".
Ref.#: 50309
 
Description: 100" opening capacity, 5 HP trim motors, 2 HP boring motors, 7.5 HP pump motor, 1/2 HP travel
Ref.#: 50023
 

Saws-Miscellaneous:

 
Description: Model 212L, 10HP, 18" blade capacity, cuts rough 2" x 12" 4" x 10", cuts /minute 45.
Ref.#: 55094
 

Shapers:

Description: Model T-120 E, magnetic starter with overload protection, self braking motor, decimal read-out for spindle height, miter gauge slot in table, 1 1/4" fixed spindle, adjustable fence and guard assembly, spindle lock, five insert rings, reverse rotation switch, five spindle speeds, electrical components meet CSA standards, emergency stop.
Specifications: Table size 43 1/4" x 31 1/2", table height 35 1/2", spindle travel 6 5/8", capacity under nut 5 1/2", max. tool dia. 9 3/4", spindle speeds (RPM) 3000, 4500, 6000, 8000, 10000, 2 dust outlets, dust outlet dia. 5 1/2" x 5 1/2", net weight 1327 lbs., warranty 1 year - electrical, 2 years - mechanical.
Ref.#: 55063

 

Description: Model DS-157.5 HP, spindle length 5-5/16", spindle diameter 1-3/16", spindle speeds 2800, 4500, 6000, 8000, 10000, RPM, slotted table, miter guage.
Ref#55047
 
Description: Model WB-85, (2) 12-1/2 HP motors, 7200 RPm, 72" table. This unit has a dust hood and 6 station clamps. 2 HP variable speed feed 220/440/3/60, (1) frequency changer, Input, 440/120/3. 25 KVA output. Brook motor pulling frequency changer. 220/440/3/60, 1750 RPM.
Ref.#: A-622
 
Description: Model WB-85, unit has 12-1/2 HP, 7200 RPM cutterheads, 2 HP, variable feed, no hold-downs, cut 85" diameter. Unit has a 20 KW frequency changer for 7200 RPM.
Ref.#: A-621
 
Description: Model 293, 56" x 47" table size, 7-1/2 HP with frequency, single fixed spindle, 1-1/4" diameter, 28" from front of table to center of spindle. The table elevation is 36". No tooling included.
Ref.#: A-738
 
Description: Model 302, (2) 10 HP motors, double spindles 1-1/4" diameter. The motors are 3600 RPM flat belted to spindles to run spindles at 7200 RPM. Each spindle has a 1/2 HP Reeves Vari-Drive to rotate pattern. It has complete dust hood and air hold downs. There is 28-1/2" between spindles. Each spindle has two cylinders to apply pattern work to cutter, each spindle has foot brake.
Ref.#: A-742
 
Description: Model 20, 1-1/8" diameter spindles on 30" centers, 5 HP direct motor drive, 54" x 38" table.
Ref.#: D-8469-C
 
Description: Model 39A, 3 HP on each spindle belt drive, spindles 30" on center, 1-3/8" spindles, table size 66" x 42". Connected 440 V.
Ref.#: 50008
 
Description: Model RS-15; 7.5hp belt drive motor; step pulley for spindle speeds of 2800, 4500, 6000, 8000, & 10,000 rpm; 1 1/4" spindle with 6" under nvt; table size of 43"l x 36"d with 18" in front of spindle; mechanical spindle brake.
Ref.#: 50299
 

Tenoners:

 

Description: Model 545; 10 ft capacity; connected 440 V; trim units - 7.5 HP; dado units - 10 HP; score units - 2 HP; cope units - 5 HP; feed units - 3 HP.
Ref.#: 50289
 

Truss Machinery:

 

Description: Model RTCF, tandem axle.
Ref.#: 50118-C
 
Description: 20 ft. capacity. Saw #1 - 5 HP, 15" blade; saw #2 - 5 HP, 15" blade; saw #3 - 5 HP, 19" blade, saw #4, 20" blade; 1 HP feed motor, open and close motor - 1/3 HP. Connected 220V.
Ref.#: 50007
 
Description: Truss Press, model TP140, 2-parts, 220/440V, 3Ph, 60Cy, connected 440.
Ref.#: 50127

 

Description: Model 51000, 5 HP, good condition, 220/440 3 Ph, 60 Cy, connected 220.
Ref.#: D-8656
 
Description: 5 HP, automatic parts stacker with magnetic control. Connected 480V.
Ref.#: D-8869
 
 

Miscellaneous:

 
Description: Model PD40-60, 4,000 pounds, 24' capacity, lift height 106", charger included.
Ref.#: 50105
 
Description: 4,000 pounds, 36' capacity. This fork lift has a rebuilt continental gas engine. Equipped with solid tires, straight shaft transmission.
Ref.#:A-886
 
 
Description: Nailer - Auto Nailer, model Thor-9, 2 HP, 48" capacity, air hold-down, 220/440V, 3PH, 60CY, connected 220.
Ref.#: 50016
 
Description: Kustom Kutter, 4 head, 20' cutting length capacity, 4-5HP saws, 16" diameter, 1-7 1/2HP scarf saw - 28" diameter, 220/440V, 3PH, 60CY, connected 480.
Ref.#: 50161
 
Description: Pallet Jack Model 48-27-500, load capacity 5000 lbs., fork heights lowered (H1) 3-1/8", raised (H2) 8", standard widths across forks (a) 27", fork width (b) 6", standard fork lengths (L) 48", load wheels 3" x 4", steer wheels 8" x 2", wheel material polyurethane/aluminum. Approx. wt. 230 lbs.
Ref.#: 55121
 
Description: Pallet Mule Model 48-27-500, load capacity 5000 lbs., fork heights lowered (H1) 3-1/8", raised (H2) 8", standard widths across forks (a) 27", fork width (b) 6", standard fork lengths (L) 48", load wheels 3" x 4", steer wheels 8" x 2", wheel material polyurethane/aluminum. Approx. wt. 230 lbs.
Ref.#: 55123
 
Description: Pallet Jack Model 48-27-500, load capacity 5000 lbs., fork heights lowered (H1) 3-1/8", raised (H2) 8", standard widths across forks (a) 27", fork width (b) 6", standard fork lengths (L) 48", load wheels 3" x 4", steer wheels 8" x 2", wheel material polyurethane/aluminum. Approx. wt. 230 lbs.
Ref.#: 55124
 
Description: Custom Made. 12" x 108, 2" rollers,
17" centers, with 8" rule bar.
Ref.#: 50143-C
 
Description: Laminating-Trim/Slitter equipped with two 1-1/4 HP cutterhead motors, with a steel constructed work table of 40" x 15", with 3/4 diameter spindles operation at 5400 RPM, max. cutter capacity of 4" dia., 2" width, max. panel thickness of 4" with one set of cutters, 24" wide x 44" long roller table Danchaert 3 roll feeder.
Ref.#: 50164
 
Description: Reconditioned, Panel cleaner model 410, size 5' top & bottom brushes. Unit used to clean panel before going through Glue Spreader.
Ref# D-8486
 
Description: Model 800C, feed belt with 30" x 132" capacity. This was used on Buss 44 planer as infeed belt.
Ref.#: D-8860-C
 
Description: Model 801-24, 2' x 10' roller, 8' rule bar with kicker and 11 stops, rollers are powered with 3/4 HP motor. Connected 220V.
Ref.#: D-8861-C
 
Description: Anver Vaccum Pod, 12".
Ref.#: 50101
 
Description: FP3000 LH; 10' useable; table & legs 10' useable.
Ref.#: 55135
Description: Model MH620; 20 ft; connected 220 V; blade # 1 & 2/multiple/14" blade/5 HP/3450 RPM; blade #3/scarfing/ 30" blade/7.5 HP/1725 RPM; blade #4/multiple/22" blade/5 HP/1725 RPM; blade #5/multiple/14" blade/5 HP/3450 RPM; blade #6/cut off/ 22" blade/5 HP/1750 RPM.
Ref.#: 50257
 
 

Prices subject to change. All prices are FOB shipping point. These listings should not be considered as a formal quote. Please call or e-mail us for further information.

 

| About Our Company | New Products | Stamping Products | Parts | Service Tech | Home | Comments |